• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace window pane Window Panes

A damaged window pane can be a nuisance. This could be an opportunity to upgrade to energy-efficient windows or insulated ones, and reap advantages like improved comfort, increased resale values and reduced utility costs.

It's a project you can tackle yourself at less than the cost of hiring a professional. It requires the right equipment and an hour or two of your time.

Glass

If your single-pane windows are outdated broken, deteriorating or damaged, replacing them with newer glass that is tempered or insulated can increase energy efficiency and reduce noise while also preserving the historic integrity of older homes. The replacement of the window pane is simple and can be done by homeowners with basic hand tools. You will also require an extra window pane, glazier's tips, pliers, and latex glazing putty. If necessary, you can use a heating gun to warm the old putty. Before starting, wear gloves and safety goggles as working with broken glass could cause injuries.

Begin by removing any remaining broken pieces of glass. It is recommended to use pliers however, a flathead may be used as well. Then, use a wooden chisel or putty knife remove the remaining old putty from around the frame and sash. Be careful to not scratch the window sash. Take your time and work slowly. It is best to do this on a stable ladder rather than on the ground and have someone stand below the sash to help keep it steady.

After you've removed all the old putty, you can prepare the window frame for the new pane. To allow for seasonal expansion or contraction by subtracting 1/8 inch from the measurements of width and height. Take these measurements to the nearest hardware store or home center, and find a piece glass cut to size. You can cut the glass yourself if you possess the right tools.

After installing the new pane, run a small bead of caulking along the edge to make it weatherproof. Then, you can install a glazier's pointing on the frame's opposite side to secure the pane into its place. The points shouldn't be tight enough to cause friction between the frame and sash However, they should not be loose.

Before applying the putty, work it in a gentle manner until it is soft and free of lumps. Make it into pencil-sized strips. Apply the first strip to the corner of the frame, moving from one corner to another to ensure it is even and smooth.

Glazier's Points

The glazier's points are tiny triangular metal pieces which help to secure the glass into the window frame without causing damage to the delicate surface. It's easy to understand how to use this secret tool and you can save money on the expense of an expert installation.

After getting rid of the old putty glazier points and any residue, clean the frame thoroughly using an utility knife. Lightly sand the frame in the rabbet grooves, if necessary, to smooth rough areas. If you decide to sand wood, protect it with painter's tape to protect it from damage caused by accidental sanding.

Take the dimensions of the frame and write down accurate measurements. These measurements can be taken to a home center or hardware store and the new pane will be cut slightly smaller. This will ensure that the pane fits comfortably and allows for Replace Window Pane expansion and contraction.

Insert the new pane into the frame and press it down with your hands. Make use of the chisel's point or the back of the putty blade to tap in the glazier's points as shown in Figure 11. When you're done, they should be flush with the top edge of the pane and the raised shoulders of the points should be just below the rabbet's lip. groove.

Apply a thin layer of glazing compound to the rabbet grooves and the edges of new glass. This will protect and seal the edges. Let it dry and cure completely.

When the glazing compound is dry it's time to put in the new window sash. The first step is to coat the wood with a heavy coat of linseed oil. This will prevent the newly-created putty from drying out and cracking when it absorbs moisture. Apply the coat using a brush or the tip of your putty knife, and then use the chisel, or the back end from the putty knife to gently hammer in the new sash and glazier's point into the rabbet grooves. Repeat this procedure every 10 inches along the perimeter of the frame.

Putty

A baseball hit, a rock thrown in error, or a tree falling could result in a broken or cracked window pane. Fortunately, the majority of windows can be replaced by simply placing a new piece in the right place. The glass is held into position by a small metal clip, called a glazier’s point and putty. This compound is also called glazing compound. Before you install a new pane, first get rid of the old one and clean up the area using an abrasive and a pull-type paint scraper or an abrasive wood chisel. Wear protective glasses and gloves while you do this work. You'll require a heat gun when the window is fixed into the frame.

If you're planning to install the original sash, gently remove the molding pieces that are used to secure the old pane. Then, sand the sash to ensure it's level and ready to be re-caulked. After the sash has been installed it is possible to apply a silicone caulk on the glass. This will ensure that it won't be leaking or fade over time.

Remove the glazing points from the rabbets and the grooves in the sash, where the glass sits. If they're difficult to work out, try placing the hand tool, such as a heat gun to soften them first. If you're using a heat gun, make sure not to scratch the sash or its railings by placing the tool too closely.

Once the old glaze points and putty are removed, make a bed for the new pane. Roll a rope of glazing compound between your fingers and make it about 1/2 inch thick. Then, you can press it into the rabbets in which the glass will be. The glass must be positioned against the putty on both sides. If necessary, lightly tap your glass into the rabbet using your thumb.

If the new pane is cracked, you can use a silicone caulk or glass glue made from solvents to fill in the crack before pressing it into the sash. If the crack isn't sealed, you will require putty to keep water from getting in. After the putty has dried, wipe the oily film off the glass and allow it to dry completely before painting. Paint after the putty has dried completely. It won't form a good seal and could discolor or leak over time.

Paint

If you've suffered a break in a replace window handle pane, you might be worried about the expense of a new one. However, replacing a single glass pane doesn't have to break the bank when you do it yourself. Even a double-paned window can be replaced for a fraction of what it will cost a professional.

If you're working with large glass windows first, ensure that it is securely attached to the frame. Using the proper tools and techniques to make this task relatively easy and fast.

When you are ready to start with the removal of the window screen replacement pane. Pry out the metal glazing points attached to it. These are tiny triangles of metal that act as "nails" that hold the window in place. They are submerged beneath a glaze putty or bead that hardens to an unbreakable wedge that holds the wood frame securely in place and conceals the edges.

Once you have the old pane removed clean the surrounding frame and wood. Scrape off any paint that has been used, and sand the rabbet grooves in which the glazing points were. These should be sanded down to bare wood so that you can paint them the same color as the rest of the frame. After sanding, apply a coat of flax oil to the bare wood to prolong its life.

The next step is to determine the size of the window opening. It is necessary to take vertical and horizontal measurements of the entire opening, and also the thickness of the old pane. To determine the exact size of the new pane subtract 1/8 inch from both measurements. This will allow for seasonal changes in the glass. You can take these measurements to a hardware store or home improvement shop and get the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.